FREE SHIPPING & LIFETIME WARRANTY

Rhinohide Canopies

Product has been added to your cart.
Rhinohide Canopy on John Deere 1025R
Side View of Rhinohide Canopy on John Deere 1025R with Angled Roll Bar
Angled View of Rhinohide Canopy on John Deere 1025R with Angled Roll Bar
Canopy Support Arms Under Rhinohide Canopy
Rear View of Mounting Hardware on Angled Roll Bar
Mounting Hardware on Angled Roll Bar
Under View Close-Up of Canopy
Rhinohide Canopy Shell Length x Width Dimensions
Rhinohide Canopy Shell Profile Dimension
Rhinohide Canopy on Angled Roll Bars
Rhinohide Canopy on John Deere 1025R
Unbreakable Tractor Canopy
Side View of Rhinohide Canopy on John Deere 1025R with Angled Roll Bar
Angled View of Rhinohide Canopy on John Deere 1025R with Angled Roll Bar
Canopy Support Arms Under Rhinohide Canopy
Rear View of Mounting Hardware on Angled Roll Bar
Mounting Hardware on Angled Roll Bar
Under View Close-Up of Canopy
Rhinohide Canopy Shell Length x Width Dimensions
Rhinohide Canopy Shell Profile Dimension
Rhinohide Canopy on Angled Roll Bars

Rhinohide Canopy for Angled Roll Bars

$499

Accessories

Limited Time Option -$35

These shells have all the same resilience as our factory firsts, but they either show an uneven trim or an excessive bow.

Total: $499

Do you have a tractor with a roll bar that angles forward? The Rhinohide Canopy will fit angled roll bars because we designed support arms for roll bars like these.

The most common tractor with an angled roll bar is the John Deere 1025R. But TYM, Rural King, Mahindra, and Bad Boy also have tractor models with angled roll bars.

Not all angled roll bars need our special support arms—if your roll bar angles forward less than 15°, you can and should use our Universal Tractor Canopy.

Rhinohide Canopy Highlights

The Rhinohide Canopy is a universal canopy system designed for any tractor or mower with a Roll Over Protection System (ROPS), otherwise known as a roll bar.

Only the Rhinohide Canopy is removable, lightweight, virtually indestructible, and can mount below the top of your roll bar. And our canopy is 100% made in America.

True to its name, the Rhinohide Canopy is virtually unbreakable—made from a very high strength and lightweight plastic (HDPE). We have yet to hear of an encounter too strong for the canopy, yet at just 13 lb the shell is still lightweight enough for anyone to handle.

When metal will dent, scratch, or rust, the Rhinohide barely shows a marks. When Fiberglass or other plastics like ABS will crack or shatter, the Rhinohide looks like new.

Remove your Rhinohide Canopy in ten seconds with the twist of two hand screws, helpful if you need to remove the canopy for trailering, or for low-clearance areas on your property or a low barn door. And it’s especially handy if you’re moving the canopy to cover your backhoe, or over to your mower using our Multi-Kit (see more info below).

Canopy Position

Our canopy is 37″ wide x 45″ deep. The closer you mount it to your head, the more shade provided. The best position for the canopy is about 10 to 15 inches above your head. On tractors, this often means mounting in front of and below the top of the roll bar.

Depending on the position of your seat, and position and design of your roll bar, this may or may not allow for much rear head coverage. So you can opt to mount above the roll bar, too. If you are planning to mount above your roll bar, you should use our Universal Tractor Canopy, as there is no need for the support arms for angled roll bars.

 

It doesn’t matter if your tractor is from John Deere, Kubota, Kioti, Mahindra, Massey, LS, Yanmar, TYM, Bobcat, New Holland, Bad Boy, Summit or any other manufacturer!

We have hardware to fit 100% of roll bars out there. The standard hardware on our Universal Tractor Canopy fits 90% of tractor roll bars. To be sure you don’t need special hardware, it’s best to verify four things.

  • A) If your roll bar is wider than 42 inches (outside-to-outside), choose that option.
  • B) If your roll bar is made from tube steel wider than 2.5 inches, choose that option.
  • C) If your roll bar is made from tube steel deeper than 4 inches, choose that option.
  • If your roll bar angles forward greater than 15 degrees, shop our Canopy for Angled Roll Bars.
Roll Bar Critical Dimensions for Rhinohide Canopy

The Rhinohide is pretty straightforward. Still we have a few things worth considering:

Backhoe Kit
If you use a backhoe, add a second set of mounting hardware to move your canopy from the front to the back. Not compatible with angled roll bar.

Multi-Kit
If have two machines with roll bars, you maybe able to buy one canopy and two mounting kits to swap the canopy from one machine to the other. Read below for more information about the Multi-Kit compatibility.

Grab Handles
Increase or decrease your grip stance with our grab handles. These slip over the canopy support arms and set in place anywhere you’d like with two set screws.

5 ways our canopy beats the competition

We fit every tractor & mower

If your tractor or mower has a roll bar, you can use a Rhinohide Canopy.

Straight or angled.
Square, rectangular, or round.
Our standard hardware fits 95% of roll bars, and we have parts to fit the remaining 5%.

Unbreakable (Almost)

The Rhinohide Canopy is made from a very high-strength, lightweight plastic called HDPE.

Our shell absorbs impact when other plastics (or even metal) would crack, shatter, or dent.

There is no paint to peel or scratch off, and no rust either. Scratches are barely visible since our canopy is black all the way through.

Easy on, easy off

Need to drive in the woods?
Get under a low door?
Trailer your machine?

Remove your canopy in 10 seconds by loosening the two hand screws, and sliding off your canopy.

*Add our Grab Handles if you want to widen or narrow your grip stance.

Mount above or below

Traditional canopies only mount above the roll bar. But the Rhinohide can mount above or below, depending on your preference.

Our standard hardware supports either mounting location.

Made in the Heart of the USA

The shell, the steel, fabrication and powder coating, the hardware, and even the box it ships in.

From start to finish, a Rhinohide Canopy is completely made in the heart of America—Kansas.

Frequently Asked Questions

The most commonly asked questions are answered here.For even more questions, visit our full FAQ page.

The Rhinohide Canopy mounts to the roll bar of a tractor or mower, and we haven’t found a roll bar that we don’t fit.

But to know if you can use our standard hardware or need our pieces for larger sizes, please confirm the following three dimensions.

  1. Roll Bar Tube Steel Width
    • Our standard U-bolt fits tube steel up to 2.5 inches wide.
      If your roll bar is made of tube steel wider than this, please select “Roll Bar Wider than 2.5 inches” up above.
  2. Roll Bar Tube Steel Depth
    • Our standard U-bolt fits tube steel up to 4 inches deep.
      If your roll bar is deeper than 4 inches, please select “Roll Bar Deeper than 4 inches” up above.
  3. Roll Bar Overall Width
    • Our standard L-Brackets fit roll bars up to 42 inches wide, measured outside-to-outside.
      If your roll bar is wider than this, please select “Roll Bar Wider Than 42 inches” up above.

Canopy Shell

Size: 37 x 45 x 2.5 in (W x L x H)
Weight: 13 lb
Color: Black
Material: HDPE Plastic

Support Structure

Mounting Supports: Black, Powder Coated Steel
Hardware: Zinc Coated Steel

Shipping Box

45 x 38 x 4 inches (W x L x H)
Shipping Weight: 34 lb

Shipping

  • Shipping is included in the price of your canopy
  • Orders ship the next business day (exceptions apply)
  • All products ship UPS Ground
  • You will be emailed a tracking number once we print your shipping label

Returns

  • You can return your canopy within 90 days of purchase
    • All materials must be in as-new condition
    • Customers are responsible for return costs
      • We can provide a return label, but the cost will be deducted from your return
  • Please contact us if you wish to return your canopy

One person can install a Rhinohide Canopy in about 30–40 minutes.

Installation requires the following tools:

  • 3/4″ Socket or Open Wrench
  • (2) 1/2″ Sockets or Open Wrenches
  • 3/8″ Drill (Drilling Thru Plastic Shell Only)
  • Tape Measure
  • White Wax Pencil (optional)

Will the Rhinohide Canopy
fit my roll bar?

Yes we will.

Our standard hardware fits 98% of tractors we sell to.
And we have hardware to fit the rest, too.

(Read on →)

Roll Bar Critical Dimensions for Rhinohide Canopy

It’s as easy as ABC

Verify these three measurements to ensure you get the right hardware the first time.

A: Measure the outside-to-outside width of your roll bar.
If it’s greater than 42 inches, select that option above.

B: Measure the width of your roll bar’s tube steel.
If it’s wider than 2 1/2 inches, select that option above.

C: Measure the depth of your roll bar’s tube steel.
If it’s deeper than 4 inches, select that option above.

But my roll bar isn’t straight…

Can I still use a Rhinohide Canopy?

Yes. We have designed two support arms that work for all roll bars.

(Read on →)

Standard Roll Bar Angle Allowance Diagram

This is what we consider a Standard Roll Bar.

The vast majority of tractor models (95%+) have a roll bar that doesn’t lean forward or backwards more than 15°. We consider anything in this range a Standard Roll Bar, and it fits our standard hardware in the Universal Tractor Canopy.

All zero turn roll bars also classify as Standard, for our purposes, so the Universal Mower Canopy fits all zero turn mowers.

(Read on →)

Angled Roll Bar Diagram

This is what we consider an Angled Roll Bar.

We designed a support arm to match the angle of the roll bar on the John Deere 1025R and 2025R.

That same support arm works for angled roll bars from TYM, Rural King, Bobcat, Bad Boy, Mahindra, and Branson.

If your roll bar looks like this, be sure to order our Canopy for Angled Roll Bars.

Improve your grip with Grab Handles

Our handles are angled at 45° allowing you to increase or decrease your grip stance.

The handles are sold as a pair and slide over the support arms to any desired position.

Rhinohide Canopy Shell Top View
Rhinohide Canopy Side Profile

We back our canopy for life.

We haven’t had to replace a canopy yet,

and we don’t expect you to be the first.

Each canopy comes with our simple-to-understand Lifetime Warranty—if anything goes wrong because of something we did, contact us.

We’ll make it right.

Our Lifetime Warranty is simple—if anything goes wrong because of something we did, contact us.

We’ll make it right.

Customer Reviews